Gecko [ 167.86.127.34 ]

Name	Size	Permission
functions.sh	4.06 KB	-rw-r--r--
parameters.sh	2.89 KB	-rw-r--r--
pktgen_bench_xmit_mode_netif_r...	2.72 KB	-rwxr-xr-x
pktgen_bench_xmit_mode_queue_x...	1.92 KB	-rwxr-xr-x
pktgen_sample01_simple.sh	1.94 KB	-rwxr-xr-x
pktgen_sample02_multiqueue.sh	2.23 KB	-rwxr-xr-x
pktgen_sample03_burst_single_f...	2.63 KB	-rwxr-xr-x
pktgen_sample04_many_flows.sh	2.55 KB	-rwxr-xr-x
pktgen_sample05_flow_per_threa...	2.31 KB	-rwxr-xr-x
pktgen_sample06_numa_awared_qu...	3.05 KB	-rwxr-xr-x

Code Editor : pktgen_bench_xmit_mode_netif_receive.sh

#!/bin/bash
# SPDX-License-Identifier: GPL-2.0
#
# Benchmark script:
#  - developed for benchmarking ingress qdisc path
#
# Script for injecting packets into RX path of the stack with pktgen
# "xmit_mode netif_receive".  With an invalid dst_mac this will only
# measure the ingress code path as packets gets dropped in ip_rcv().
#
# This script don't really need any hardware.  It benchmarks software
# RX path just after NIC driver level.  With bursting is also
# "removes" the SKB alloc/free overhead.
#
# Setup scenarios for measuring ingress qdisc (with invalid dst_mac):
# ------------------------------------------------------------------
# (1) no ingress (uses static_key_false(&ingress_needed))
#
# (2) ingress on other dev (change ingress_needed and calls
#     handle_ing() but exit early)
#
#  config:  tc qdisc add dev $SOMEDEV handle ffff: ingress
#
# (3) ingress on this dev, handle_ing() -> tc_classify()
#
#  config:  tc qdisc add dev $DEV handle ffff: ingress
#
# (4) ingress on this dev + drop at u32 classifier/action.
#
basedir=`dirname $0`
source ${basedir}/functions.sh
root_check_run_with_sudo "$@"

# Parameter parsing via include
source ${basedir}/parameters.sh
# Using invalid DST_MAC will cause the packets to get dropped in
# ip_rcv() which is part of the test
if [ -z "$DEST_IP" ]; then
    [ -z "$IP6" ] && DEST_IP="198.18.0.42" || DEST_IP="FD00::1"
fi
[ -z "$DST_MAC" ] && DST_MAC="90:e2:ba:ff:ff:ff"
[ -z "$BURST" ] && BURST=1024
[ -z "$COUNT" ] && COUNT="10000000" # Zero means indefinitely

# Base Config
DELAY="0"        # Zero means max speed

# General cleanup everything since last run
pg_ctrl "reset"

# Threads are specified with parameter -t value in $THREADS
for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do
    # The device name is extended with @name, using thread number to
    # make then unique, but any name will do.
    dev=${DEV}@${thread}

# Add remove all other devices and add_device $dev to thread
    pg_thread $thread "rem_device_all"
    pg_thread $thread "add_device" $dev

# Base config of dev
    pg_set $dev "flag QUEUE_MAP_CPU"
    pg_set $dev "count $COUNT"
    pg_set $dev "pkt_size $PKT_SIZE"
    pg_set $dev "delay $DELAY"
    pg_set $dev "flag NO_TIMESTAMP"

# Destination
    pg_set $dev "dst_mac $DST_MAC"
    pg_set $dev "dst$IP6 $DEST_IP"

# Inject packet into RX path of stack
    pg_set $dev "xmit_mode netif_receive"

# Burst allow us to avoid measuring SKB alloc/free overhead
    pg_set $dev "burst $BURST"
done

# start_run
echo "Running... ctrl^C to stop" >&2
pg_ctrl "start"
echo "Done" >&2

# Print results
for ((thread = $F_THREAD; thread <= $L_THREAD; thread++)); do
    dev=${DEV}@${thread}
    echo "Device: $dev"
    cat /proc/net/pktgen/$dev | grep -A2 "Result:"
done

${this.title}

Code Editor : pktgen_bench_xmit_mode_netif_receive.sh